Sewing Blog

The Golden Rule for Matching Up Seams

Sewing pattern pieces come in all kinds of unusual shapes, and sometimes it’s a challenge to figure out how they match up. Today, I’m sharing the golden rule for matching up seams. You’ll want to remember this one.

Sewing seams for a garment

Here it is: To assemble the pattern pieces properly, you need to use the seam allowances as your guide.

Take the puzzle out of patterns by paying attention to the alignment of the edges and your result will be perfect.

To help you really understand this concept, I’ll walk through three common types of pattern pieces that confuse many sewers. You’ll see the rule in action and then can apply the learning to all other seams.

This is a common issue when sewing shoulder seams.

jacket shoulder seam edges

For example, look at the shoulder seams on the jacket front and back pattern pieces shown above. The length of the front shoulder seam edge appears longer than the back shoulder seam edge.

The key to stitching this up correctly is to match at the stitching line, not at the fabric’s cut edge.

shoulder match at seam allowance

When you match up the edges at the precise point where the stitching line lands at the edge of the fabric, then the two pattern pieces match up perfectly.

You can see the small, triangular bit of extra jacket front fabric (in pink) that peeks out from under the jacket patten piece. This is perfectly fine, and pattern designers do this intentionally: When the seam allowance is pressed open, that extra bit will be caught in the stitching of the next part of the garment assembly. 

shoulder seam pressed open

FREE Guide: Fitting Fundamentals for Sewers

FREE Guide: Fitting Fundamentals for Sewers

Learn fitting fundamentals for sewing breathtaking projects that flatter any body style!Get the FREE Guide

Another place where this situation occurs is with princess seams.

Every designer or pattern company might deal with this issue differently. If you get in the habit of visualizing the stitching line on your fabric, then you will have no trouble with matching up the seams to sew.

back princess pattern pieces

This example is the back of a dress with  princess seams. The side back portion does look longer than the center back piece in red. 

princess seam incorrect alignment with text

If you start at the edge, then the pattern pieces will not match up correctly, as you can see above.

Instead, match the pattern pieces where the stitching line intersects with the edge of the garment. 

align princess seams at seam allowance

With princess seams in particular, there’s sometimes a triangular bit that sticks out (as you can see with the yellow fabric above). That is intentional, and allows you to sew the two pieces together. 

princess seam matched up correctly

Here’s the completed princess seam. You can see that the armhole now has a continuous curve from shoulder to armhole and the notches match. 

Another spot where the seam alignment is a bit tricky is the inseam of pants.

pants front and back pattern pieces

When sewing pants, you stitch together the front and back pieces at the inseam

pants seam matched incorrectly

Lining up the edges of the pattern pieces, as I did below, is incorrect.

pants seamed incorrectly example

This results in uneven edge when the seam is stitched. Here the difference is about ¼”. If you were to ignore that and cut the excess off, then you’ve changed the crotch seam, so it will be made too long or too short for fit.

To sew them together correctly, line up the cut edges of the pattern front and back, with the stitching lines intersecting.

correct seam alignment on pants inseam with text

Now your crotch seam is a smooth curve and the fit is not changed. 

smooth seam when sewn at seam allowance

Two-piece sleeves have this same situation (you read see more about matching up sleeve seams in this Craftsy Blog post).

You can see that what many of these examples have in common are pattern pieces that end in a sharp angle, or a situation where you are joining a straight piece to an angle. Just remember to line up the seam allowances, not the edges, and you’ll be set for success.

FREE Guide: Fitting Fundamentals for Sewers

FREE Guide: Fitting Fundamentals for Sewers

Learn fitting fundamentals for sewing breathtaking projects that flatter any body style!Get the FREE Guide

6 Comments

Jennifer

Thank you! That is really great info. I was rushing last night to make a pair of comfortable ponte yoga pants for my daughter’s field trip to the Topsfield Fair this morning with school. I lined up the crotch incorrectly, and the front and back panels had a noticeable difference. I served off the excess with the sewing of the waistband, which did change the cut. I think they’ll still fit her (she hasn’t seen them yet!) but next time I’ll be more careful to follow the rule, “line up the stitching lines, not the edges!”

Reply
Jennifer

Serged, not served. Sorry!

Reply
Laurie

Thanks so much for this! I’ve been confused by this for 40 years and stretching to make things fit! 😀

Reply
Elizabeth

That’s it!! Didn’t know how to line up the seams…making the Pattern pieces fit..looks and fits homemade!!
Thanks for the clarification!!

Reply
Ann MacDonald

Thank you for all your helpful advice for those of us who can use your expertise in sewing problems.

Reply
PT

Thanks for helping me appreciate my Mother who taught me all these things a an early age.
You might want to have your captcha provide better pictures…

Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

Leave a Reply