Sewing Blog

How to Re-thread Your Sewing Machine in 4 Steps

You’ve decided to dig your sewing machine out of the closet and tackle the really cute project you just found on Craftsy. Good for you! Let’s get that machine threaded so you can get on with being creative.

These detailed instructions and photos will make the process simple. Once you’ve finished, un-thread it and try again. You’ll quickly find threading your machine is simper than it looks — you will quickly memorize how to do it for next time!

How to Re-thread Your Sewing Machine in 4 Steps

The machine used for this tutorial is a Janome 2030QDC. Other machines will be similar, but if you have questions, please refer to your specific machine’s manual.

You will need:

Get to Know Your Sewing Machine

sewing class

Whether you need to solve common sewing machine problems or want to brush up on the anatomy of your machine, you’ll get better results after watching this FREE Craftsy mini-class.Enroll FREE Now »

How to re-thread a sewing machine

Step 1: Fill the bobbin

Place the thread on spool pin (A) and cap it with the spool holder (if applicable). The thread should be coming off of the spool towards the back of the machine.

Thread on Spool Pin

Draw the thread through the bobbin thread guide (B). Place the bobbin on the bobbin winder (C). Feed the thread through a hole on the bobbin to hold it in place.

Thread ready to wind the BobbinFeed thead through bobbin

Holding the thread loosely, push the bobbin winder to the right against the stopper. Start winding the bobbin with the foot pedal or start/stop button. Wind a short ways while holding the thread. Then stop, clip the thread and continue. The machine should stop when the bobbin is full.

Wind bobbinClip Thread and Continue Winding Bobbin

Clip the thread, remove the bobbin and set aside.

Step 2: Thread the machine

Note: It is best to thread the machine while it is turned off.

Bring the thread around the upper thread guide (D), then bring it down and around the U-shaped guide (E) in the front of the machine. Hold the thread taut to make sure it engages with the tension discs (F).

Thread Machine through Upper Thread GuideBring Thread Through U-Shaped Guide-

Turn the handwheel on the side of the machine to move the take-up lever (G) to it’s highest position. Draw the thread around it (or through it on some machines) to secure it in the eye of the take-up lever.

Draw Thread into Take-Up Lever Eye

Bring the thread down the left side of the U-shaped guide to the needle area.

Bring thread down to needle area

Feed the thread through the last one or two thread guides (H) and thread the needle.

Feed thread through last thread guidesThread the Needle

Step 3: Insert the bobbin

This applies to top-loading machines. For any other machine, consult your instruction guide.

Remove the bobbin cover plate. Place the bobbin in the case with the thread running counter-clockwise.

Bobbin Thread runs Counter-Clockwise

Bring the thread through the first notch (I) and draw the thread to the left until it slips into the second notch.

Draw Thread through notches
Pull out a 6″ – 9″ thread tail to use in the next step.

Step 4: Draw up the bobbin thread

Hold the machine thread taut and turn the handwheel to raise and lower the needle. This will pick up the bobbin thread (J).

Turn handwheel to raise bobbin thread

Pull gently to bring up the entire bobbin thread. Pull both threads to the back of the machine, under the presser foot.

Pull both threads out to the back of the machine

Now you’re ready to start sewing!

Get to Know Your Sewing Machine

sewing class

Whether you need to solve common sewing machine problems or want to brush up on the anatomy of your machine, you’ll get better results after watching this FREE Craftsy mini-class.Enroll FREE Now »

11 Comments

pat bingham

Like your site. I own3machines. Baby lock embroidery, server and sewing machine

Reply
Sherri | Thread Riding Hood

So good to hear from you Pat! Thanks for taking the time to comment. I don’t have an embroidery machine as yet – but they sound wonderful!

Reply
Dorothy

I am unable to adjust the tenson properly. Top looks fine but the bobbin side has loose top stitching all along the seem.

Reply
jackie watson

When picking up the bobbin the threads just get caught up in the machine and when pulling up the thread this does not pull up the bobbin thread which is all caught up under needle plate! Help

Reply
Sherri Sylvester

Hi Jackie – is the bobbin inserted correctly? The bobbin thread should spin in the direction your machine manual says to be brought up correctly. If this is correct you could also try cleaning out the inside of the bobbin case and under the needle plate. Maybe something is stuck there that is causing a problem. Hope that helps!

Reply
dee

I can’t get the take up thread to pull up the bobbin thread below?

Reply
Master blaster

Thanks for the info it was very informative

:):):):):):):):):):):):):):):):):):):):):)

Reply
Audrey

M using an empirial sewing machine and the thread keeps on breaking when I trie to sew

Reply
Kristy

I’ve done everything as described but once i start sewing something locks up and the bobbin stops moving. Im using a metal bobbin though. Could this be the problem?

Reply
Sherri | Thread Riding Hood

Hi Kristy – is the bobbin inserted correctly? The bobbin thread should spin in the direction your machine manual says to be brought up correctly. If this is correct you could also try cleaning out the inside of the bobbin case and under the needle plate. Maybe something is stuck there that is causing a problem.

Reply
Sarah

Well….this is a rally nice site. The article is very nice. Thanks for sharing!

Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

Leave a Reply