Card Making

Fancy Folds: How to Make a Cute Triangle Trifold Card

Your friends will flip for this triangle trifold card! It comes together with just four easy scores and folds, tied closed with a ribbon or snapped closed with hidden magnetic discs. The result is a square, 3 1/2″ if using a standard 8 1/2″ x 11″ piece of cardstock or 4″ if using 12″ x 12″. No matter your finished size, create a quick coordinating envelope with our simple tutorial on how to make an envelope in just minutes. 

Finished trifold card

Fancy Folds: 4 Fun Tutorials for Folding Cards

Fancy Folds: 4 Fun Tutorials for Folding Cards

Create smile-spreading cards with just a few simple folds with expert tips and insider tricks to make your loved ones feel extra special.Get the FREE Guide »

How to make a trifold card

Note: For this tutorial, I’ve used an 8 1/2″ x 11″ piece of cardstock, resulting in a 3 1/2″ square card. I used small magnetic discs hidden between the paper layers to hold the card closed, but have also included instructions for using ribbon to hold the card closed. 

Supplies for making a trifold card

Supplies you’ll need:

  • Scor-Pal or other scoring board
  • Bone folder
  • Cardstock
  • Patterned paper (I used Dear Lizzy Day Dreamer 6×6 by American Crafts)
  • Adhesive
  • Paper trimmer
  • Stamps (I used Twiggy Florets and Flap Happy by Paper Smooches)
  • Black ink (I used Black Licorice hybrid by My Favorite Things)
  • Copic markers (I used B21, B34, E50, E53, E57, G40, G43, R81, R83, Y21, YR23)
  • BasicGrey small magnetic discs (two positives, two negatives)
Step 1 Cut and score to create equal panels

Step 1:

Cut cardstock base to 3 ½” x 10 ½”. Score at 3 ½” and 7”. The paper should now be scored/divided into three equal squares.

Step-2-and-3 Score end squares diagonally

Step 2:

Diagonally score left square from upper left corner to lower right corner.

To do this, I chose a random spot across the top of my score board. I dragged my bone folder down, placed the upper corner of my cardstock at the chosen mark (5″ as shown on the left above), then shifted the cardstock until the bottom right corner aligned with the 5” groove. By dragging the bone folder down and holding in that position, I was assured to score along the correct groove.

Step 3:

Turn cardstock and repeat, diagonally scoring the opposite square. It is important that both diagonal scores (Steps 2 and 3) are in the same direction.

Step 4 and 5 Fold along score lines

Step 4:

Fold cardstock ends up at 3 ½” and 7” score lines.

Step 5:

Fold cardstock ends down at diagonal score lines.

Step 6 and 7 Cut patterned paper to size

Step 6:

Cut patterned paper to 3 ¼” x 3 ¼”.

Step 7:

Diagonally cut patterned block into two pieces.

Step 8 and 9 Adhere magnets between paper layers

Step 8:

Remove adhesive backing from one positive disc and adhere to back side of one patterned triangle. I placed the disc close to the right angle corner, far enough away from the edge to leave room to apply adhesive around all edges.

Step 9:

Adhere patterned triangle to one side of closed trifold card, over magnet. (Bone folder is in place to hold the card closed for photography purposes.)

Step 10 and 11 Magnets hidden between layers

Step 10:

Repeat Steps 8 and 9 with remaining positive magnetic and triangle of patterned paper.

Step 11:

Open card as shown. Without removing adhesive backing from negative discs, allow each magnet half to “stick” to each positive half (through the cardstock).

Step 12 Magnetic discs adhered to inside panel

Step 12:

Remove adhesive backing from negative halves and close the card, pressing firmly over both magnets. When card is opened, the negative halves should now be adhered to the center panel, in perfect alignment with the magnetic halves hidden beneath the patterned triangles.

Step 13 Finished inside panel adhered

Step 13:

Cut a 3 1/4″ x 3 1/4″ block of white cardstock. Stamp and embellish as desired and adhere to inside panel.

Note: A handwritten message can be written before adhering the panel, or just be aware that the magnetic discs, while very thin, could slightly impede smooth penmanship.

Step 14 Create front panel

Step 14:

Decorate front panel as desired. My white cardstock is cut to 2 3/4″ x 2 3/4″ then matted with a thin pink border to allow the patterned paper to show beneath.

Step 15 Adhere front panel

Step 15:

Apply adhesive to only one (diagonal) half of front panel and adhere to half of card front.

It does not matter whether front panel adheres to the top triangle or the bottom, but it is important to only apply adhesive to the chosen half.

As an alternative, if you do not have magnetic discs or choose not to use them, a ribbon can be used to hold the card closed. Instead of applying adhesive to one-half of the front panel, apply adhesive to the bottom edge only. Doing so will allow the ribbon to be slipped behind the front panel and tied to one side.

Finished trifold card closed Finished card, left flap open Finished card, left and right flaps open Finished card, all flaps open and flipped up

Fancy Folds: 4 Fun Tutorials for Folding Cards

Fancy Folds: 4 Fun Tutorials for Folding Cards

Create smile-spreading cards with just a few simple folds with expert tips and insider tricks to make your loved ones feel extra special.Get the FREE Guide »

3 Comments

Donna Whitten

Love this cute card, thanks for sharing!

Reply
Michele Boyer

Thank you!

Reply
Annette Siverson

I too love this cute card and it looks easy enough! TFS, Annette

Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

Leave a Reply